Схема блока питания at схема

Схема блока питания at схема
Схема блока питания at схема
Схема блока питания at схема

ATX, WTX and other standard and proprietary power supply (PSU) cables connectors pinouts

v 1.x with 20 pin connector was widely used at PC motherboard. Replaced by v 2.x with 24 pin connector

ATX specification includes not only Power Supply Unit, but also interface to case and motherboard. In addition to the old AT standard, ATX 2.0 has one extra voltage line available (+3.3V), a connector chain-lined to the single 20-pin and a power-on wire that allows Software to turn off the PSU. Nowdays this standard is obsolete and superseeded by ATX 2.2 (24 pin).

The ATX specification requires the power supply to produce three main outputs, +3.3 V (±0.165 V), +5 V (±0.25 V) and +12 V (±0.60 V). Low-power −12 V (±1.2 V) and 5 VSB (standby) (±0.25 V) supplies are also required. A −5 V output was originally required because it was supplied on the ISA bus, but it became obsolete with the removal of the ISA bus in modern PCs and has been removed in later versions of the ATX standard.
Originally the motherboard was powered by one 20-pin connector. Current version of ATX12V 2.x power supply provides  two connectors for the motherboard: a 4-pin auxiliary connector providing additional power to the CPU, and a main 24-pin ATX 2 power supply connector, an extension of the original 20-pin version.

Pin Name Color Description 1 3.3V Orange +3.3 VDC 2 3.3V Orange +3.3 VDC 3 COM Black Ground 4 5V Red +5 VDC 5 COM Black Ground 6 5V Red +5 VDC 7 COM Black Ground 8 PWR_OK Gray Power Ok is a status signal generated by the power supply to notify the computer that the DC operating voltages are within the ranges required for proper computer operation (+5 VDC when power is Ok when PSU is turned ON) 9 5VSB Purple

+5 VDC Standby Voltage (max 10mA) 500mA or more typical

10 12V Yellow +12 VDC (may sometimes have a colored stripe to indicate which rail it's on) 11 3.3V Orange +3.3 VDC 12 -12V Blue -12 VDC 13 COM Black Ground 14 /PS_ON Green Power Supply On (active low). Short this pin to GND to switch power supply ON, disconnect from GND to switch OFF. 15 COM Black Ground 16 COM Black Ground 17 COM Black Ground 18 -5V White -5 VDC (2002 v1.2 made optional, 2004 v2.01 removed from specification) 19 5V Red +5 VDC 20 5V Red +5 VDC

/PS_ON activated by pressing and releasing the power button while the power supply is in standby mode. Shorting the pin 14 (/PS_ON) to GND (COM) causes power supply to switch ON.

 

In several power supply units pin-12 may be Brown (not Blue), pin-18 may be Blue (not White), and pin-8 may be White (not Gray).  In addition, some PSU violate color coding of wires.

Pin 9 (standby) supply 5V even when PSU is turned off. Pin 14 goes from 0 to 3.7 when PSU switch is turned on.

 

 

Source(s) of this and additional information: ATX Spec v2.03 at Platform Development Support, from Hardware Book, http://www.formfactors.org/developer%5Cspecs%5CPSU_DG_rev_1_1.pdf Table 21, I have a old (2001) computer w FSP235-60GT 235W power supply w 20 pin connector, None

This page contain parts under Copyright © 2000-2015 by pinouts.ru team.
No portion of this webpage may be reproduced in any form without providing visible HTML link to Pinouts.ru . Webmaster permission required in any other cases.
Efforts have been made to ensure this page is correct, but it is the responsibility of the user to verify the data is correct for their application.

Схема блока питания at схема Схема блока питания at схема Схема блока питания at схема Схема блока питания at схема Схема блока питания at схема Схема блока питания at схема Схема блока питания at схема

Изучаем далее:



Маникюр с мятным и лимонным лаком

Ремонт турбины ккк своими руками

Схема реле в насосной станции

Как сделать 900 градусов в the crew

Поделки пасхальное яйцо своими руками из яйца
Читать новость Схема блока питания at схема фото. Поделитесь новостью Схема блока питания at схема с друзьями!